DAVIES CRAIG REMOTE ELECTRIC WATER PUMP 80LPM/21GPM EWP80 12V (#8005)

This compact pump is manufactured out of lightweight Aluminium and utilises 6 bolt flange fittings on both the inlet and outlet of the pump for superior fitment flexibility. The provided 35mm (1-3/8”) straight and right-angle push on barb fittings offer convenient fitment in any application.

With a maximum flow rate of 90 l/min (23.8 g/min), 35mm (13/8”) inlet and outlet, arrives in magnificent matt-black, powder-coated finish and offers the same high class, performance, compactness, and style you have come to expect from the world’s largest supplier of remote-mounted electric water pumps and world-beating engine cooling products company, Davies Craig Pty Ltd.

Customers continue to enjoy superior engine cooling technology using Davies, Craig’s extensive range of remote-mounted Electric Water Pumps (EWP^®) combined with the patented LCD EWP^®/Fan Digital Controller, commonly called EWP^® Combo Packs!

The EWP^®80 greatly enhances engine cooling control while giving you added power and improved fuel economy. By removing the parasitic power losses of a belt-driven, mechanical water pump the EWP^® can provide up to 10kW (13hp) of extra power and increased torque and used extensively in Intercooler applications. 

EWP^® & CONTROLLER INSTALLATION DEMONSTRATION

Combined with an LCD EWP^®/Fan Digital Controller (Sold separately Part #8002 or EWP^® Combo Pack) will manage both the EWP^® and Thermatic^® fan operation. The Digital Controller will vary the speed of the EWP^® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic^® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life. The EWP^® Controller Combo Pack is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.

The world’s most advanced total engine cooling management system:

•  Universal fit
•  More power
•  More cooling
•  Increase fuel efficiency
•  Extend engine life
•  World-leading technology

EWP^® INSTALLATION OPTIONS

Installing an EWP^® as an AUXILIARY PUMP

• Leaving the mechanical water pump in place, install the EWP^® into the bottom radiator hose.
• Remove the thermostat and drill two approx. 3mm (1/8″) holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP^® INSTALLATION – disabling Mechanical water pump

• Leaving the mechanical water pump in place, install the EWP^® into the bottom radiator hose and remove the manufacturer’s thermostat.
• You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
• If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8″) holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP^® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

• Remove the mechanical water pump and remove the thermostat.
• Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.

• Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
• Install the EWP^Ò into the bottom radiator hose.

Removed mechanical water pump (Ideal)

• Remove the mechanical water pump and thermostat from the engine.
• Install a Davies Craig EWP^® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
• Install the EWP^® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
• Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP^® will be adequately supported by the radiator hose. Where mounting is required, the EWP^® must be soft mounted to protect against vibration. For the EWP^®115, EWP^®140 and EWP^®150 Part #8700 or #8710 Mounting bracket is recommended.

Modified Engines 
Supercharged/Turbo,
Drag Racing, 4WD,
Off Road, Drifting & SpeedwayEWP^®150#8160 Sliver
#8165 Black #8161 Silver#8060 Silver
#8065 Black#8061 Silver#8970 Silver
#8975 Black#8971 SilverIntercooler
(depending on capacity)EWP^®115#8125 Nylon
#8140 Alloy#8126 Nylon
#8141 Alloy#8025 Nylon
#8040 AlloyN/A#8930 Nylon
#8950 AlloyN/AEWP^®140#8180 Alloy#8181 Alloy#8080 AlloyN/A#8990 AlloyN/AEWP^®150#8160 Sliver
#8165 Black #8161 Silver#8060 Silver
#8065 Black#8061 Silver#8970 Silver
#8975 Black#8971 Silver